Contest · Fashion · Vintage

2018 Match Your Shoes Contest Entry

1012
Simplicity 1012 View C

I spent way more time than I expected working on the Marfy blouse in January, which didn’t leave me much time to put together my entry for PatternReview.com’s 2018 Match Your Shoes Contest.

Fortunately, I already had a plan in place, so I hit the ground running when I finally started.

The black stretch fabric I used for the main color was challenging to cut. To get the best result, I used my sharpest scissors and put a fresh blade in my rotary cutter. When cutting stretch fabrics with a rotary, it is especially important to apply pressure from directly above where you want to cut. If you apply pressure at an angle, the fabric will stretch away from you as you cut. The greater the angle, the greater the distortion.

To make sure that the lace pieces would come together in a pleasing way, I first laid the lace over the pattern piece. Then I identified where the “X” stitching lines would fall. I shifted the piece until I was happy, then marked the placement with a couple of pins. I put the pattern piece on top, then cut it out. I used this process for all four lace sections. After all that, cutting the gray background fabric was a breeze!

shoe_contest_2_22
Checking the position of the flowers before cutting.

Before getting to the directions in the pattern envelope, I basted the lace and lining pieces to each other. Because my serger was ready to go, I used an overlock stitch (with the knife up) to put them together.

shoe_contest_2_23
One of the midriff pieces serge-basted

The next part was assembling the four pieces making up the front into a single piece. I have never done any quilting, but I imagine that the process is very similar. First, I sewed the top section to the right side triangle. Then I sewed the bottom section to the left side triangle. I pressed the seams open. Then I carefully pinned the two pieces so the “X” met exactly in the center. I measured twice. Then I stitched the third and final seam, pausing a few times to check and re-check my alignment. Success!

The only problem was the fabric itself. I once again needed to help the machine along by adding strips of wash-away stabilizer.

The back was made of two pieces, joined by a 22 inch zipper. So assembling the back did not require matching an “X.” Sewing those pieces was much less nerve wracking.

From this point, putting the dress together goes the same as any other back zip dress. I changed the neckline from using a facing to using bias tape, but everything else was the same as the pattern.

I put it on ready to be amazed at its awesomeness. After all, it looked great on the hanger. Alas, the fit was far from amazing. Although the fitted part of the dress (bustline and up) looked good, the loose fitting lower half was boxy and unflattering. It did not have the gentle waist curve and drape I expected from looking at the pattern illustration. Part of that was because the heavy black stretch fabric did not drape well. But I felt that the dress would be more flattering if I took in the sides a bit below the bust.

So, it was back to the sewing machine, the seam ripper and the iron. Still not happy, I added a few small darts in the back, between the waist and hip. A little while later, I had my modified style.

I trimmed the seam allowances, it hung a lot better….  but….

I still had more fitting to do. I took the sides in some more and took the darts out. Finally, it looked like I had imagined.

A quick hemming session, a final press and it was done!

shoe_contest_2_12
That’s better!

I think if I make this pattern again, I might try doing it in a mid to heavy weight knit omitting the zipper. It would be really flattering in complementary colors with topstitching. Maybe in a long sleeve version? It would also be nice in a lighter weight woven in the sleeveless view for spring and summer.

Hey – why don’t you vote for me? The voting period is from the 17th to the 22nd.

Even if you don’t vote, it’s worth taking a look at the other contest entries on patternreview.com. I’m really impressed and also have serious shoe envy.

Here is the finished look for my contest entry.

shoe_contest_2_13shoe_contest_2_10

Missed the first part of this post? Check it out here: 2018 Match Your Shoes Contest Begins.

 

 

One thought on “2018 Match Your Shoes Contest Entry

Leave a Reply