Independent pattern company Love Notions sells a pattern for a blouse with a loose, peasant style bodice entitled Rhapsody. I made one a few months ago which turned out a little small. I figured going up one size should fix that problem though.
Rhapsody has 8 different sleeve options: sleeveless, cap, short, 3/4 with cuff, 3/4 with flare, trumpet, flutter, and bishop. This one would be in a teal blue polyester woven with the flutter style sleeve.
Once you know what size you need, it’s pretty quick to make. (Especially if you have the pattern ready to go). Probably the fussiest part is making bias binding for the neck opening and sewing it neatly in place. The first top went quickly because I used pre-made packaged binding. This one was somewhat tricky because the fabric was more slippery, so I had to take my time. I think the matching binding looks pretty sharp in this case.
I’m looking forward to making this one again in some of the other sleeve styles. I can’t wait to show you!
Until then, happy sewing!
See my review of this blouse on patternreview.com here
A few years ago, I bought a cute strapless sundress. I wore it a lot that summer, then my tastes changed just enough to push it to the back of the closet. I don’t know about you, but I don’t have room in my closet for things I don’t wear!
I loved the bottom, but didn’t love the top or where the waist fell. It didn’t have pockets. By converting it into a skirt and adding some pockets, it could be transformed into a wardrobe staple.
Step 1: Deconstruction
I cut most of the bodice from the skirt, leaving a little bit of length at the waist. With my well-used seam ripper, I carefully picked out the side seams from the waist to about 2 inches below the hip.
Step 2: Pockets
Since the skirt’s gathered style gave it quite a bit of volume, I opted to hide the pockets on the inside. I found some neutral lightweight woven fabric in the scrap pile that had enough strength to handle keys and cell phones. I used a pocket pattern I had from another project (also checked to make sure it would hold my phone).
Once cut, I serged the pocket fronts and backs together, leaving the side openings alone. It doesn’t really matter if the openings match the skirt, since it is easy to close any open seams later.
I carefully pinned the pockets in place, making sure the top of the pocket was no higher than the new waistband would be.
From the wrong side, I sewed the pocket front to the skirt front and the pocket back to the skirt back. I closed the little bit of side seam opening left below the pockets.
I turned the skirt so I was now working on the right side. With my fingers, I rolled the pocket seams just slightly to the inside and carefully pressed them in place. Then I made sure they would stay that way by topstitching as close to the edge as I could get in a matching thread. One more press and I had an opening that’s practically invisible!
Fabric rolled slightly to inside and pressed
After topstitching – closed
After topstitching – open
Step 3: Elastic Waistband
There are a lot of waistband options for gathered skirts. I chose the one I thought I could do the fastest. My waistband is simply a length of wide elastic serged to the top of the skirt. I’m not even sure how long my elastic piece is – I just wrapped it around my waist and adjusted it until it felt snug. I sewed the elastic into a loop with a secure box stitch.
The rest was simple. I divided the elastic into 4 equal parts, marking with pins. I pinned the elastic to the right side of the skirt so the upper edges aligned, placing the pins at the center front, center back, and side seams. Just to make sure I distributed the elastic evenly, I pinned some more. I serged it all together using a 3 thread overlock stitch, stretching as I went.
The whole thing took a couple of hours, most of which was spent taking out the side stitches.
Coming soon, more instant gratification summer sewing.
I started out with a McCall Pattern Co. pattern 7649 printed in 1949.
The dress features:
Button front opening
Scoop front pockets
Unusual layered skirt back with many tucks and darts
Darts at waist front and back
I left the basic shape of the dress alone, but knew I would need to shorten it and modify the padded shoulder to make it wearable. Unfortunately, I didn’t notice this contest rule when I chose the pattern:
The opening must be sufficient to take the dress on and off, but does not have to be the entire length of the front.
With that fitted waist, there was no way my dress was going to qualify. My solution: extend the button opening all the way down the front and eliminate the side zipper.
I had my work cut out for me!
First order of business: unpad the shoulder. To get the shape of the bodice right, I made a muslin. I was pleasantly surprised that I didn’t need to change the length, waist, or bust. But those shoulders were awful! While still wearing the muslin, I pinched the bagginess out and pinned a new shoulder seam in place, constantly checking the back and front in the mirror. I ripped out the old shoulder seam and sewed the new one in place. Back to the mirror, I saw that it would need more adjustment. It took three tries, but I finally got it. Once I made a new pattern piece with the changes, I was ready to cut my good fabric.
Speaking of fabric… I used an Amy Butler design entitled “Cotton Blossom.” I found the cotton woven on sale at Moona Fabrics on Etsy, but I would have paid full price. It’s really good quality material and I love that color combination! Here’s some more Amy Butler on fabric.com.
I didn’t have any problems putting the top half together. The only other change I made was to add fusible interfacing to the facings and inside the collar. Since the original didn’t call for any interfacing at all, I chose Pellon SF101, which is on the lighter side for a collar. I suppose in 1949 they would have used starch to stiffen the collar. I’m grateful for the modern materials that make starch unnecessary. I finished everything but the buttons and buttonholes and set it aside.
Next – the skirt. I didn’t think I would need to make a muslin for the skirt, but when I started looking at how it went together, I was baffled. To get that cute shape in the back, there are 5 darts and 6 tucks! I felt like it would take less time to test it with a muslin than it would ripping out the inevitable mistakes.
It wasn’t difficult once I ran through it once, but it was time consuming. There was a lot more time spent marking and ironing than usual.
For the pockets, I tried to eliminate some bulk by using a lightweight woven on the inside (which does not show). The pockets turned out to be roomy and useful. Finally, I can wear a dress and not have to have a separate bag for my phone!
Here’s a little slideshow of the pockets going together.
I have to admit the next part made me nervous. I carefully cut the skirt front down the middle. I drafted a new pattern piece for the facings behind the opening. I used that to cut out two facing pieces and two more lengths of interfacing. Using the top half as a guide, I mirrored the steps I used to assemble the facings. Finally, it was time to sew the back to the front and the top to the skirt. By some kind of miracle, my math and obsessiveness worked. and everything fit!
I don’t want to do that again, but at least now I know I can.
As regular readers know, buttonholes are not my favorite thing to do. But I think I have finally turned a corner. Not flawless, but not bad!
The dress also called for a 1″ belt. I’ve never made a belt before. I was pleasantly surprised to find that it was pretty easy. I stiffened the fabric (there was a pattern piece for this) with a one inch strip of Pellon ShirTailor fusible interfacing. Then I fused a strip of heat-n-bond ultra-hold tape right on top of the Pellon. I folded over the seam allowances and just fused them to the back. Finishing was just a matter of sewing on the buckle. It was so easy that I will consider doing belts a lot more!
I finished it with a simple invisible hem. I’ll definitely be wearing this dress a lot. It looks good on its own, but can also work under a sweater or other layers. I am really happy with the result, but I think I am ready for something quick and easy next time!
Check out all of the shirtdress contest entries here.
The dress must include a front opening that has button closures.
The opening must be sufficient to take the dress on and off, but does not have to be the entire length of the front.
The dress must be at least mid-thigh.
I have a few shirtdress patterns from the last few years, but a flea market find printed in 1949 seemed a little more special. I love the attitude of the popped collar. The scoop front pockets are big and useful. The back has some interesting tucks and darts that add volume and interest. In my opinion, only two things hold it back from being a modern design: the length and the wide, padded shoulders. I figured those would be easy enough to edit and dove in.
About Vintage Patterns
Everyone has their own idea about what vintage means. If you were born in 1998, something from 1997 might be considered vintage. Others might start much further back. For me, I think I start with patterns made before body/size measurements became standard for the major pattern companies – around the early 1970’s.
Some things have been the same for a long time.
Pattern printed on that same brown tissue paper
Seam allowance is 5/8″
Pattern markings such as triangles and dots are the same and used for the same purposes.
The illustrated envelope and included instructions are very similar.
Other things have changed over the years.
Sizing: no multi-size patterns. The pattern is printed for a single size only. This one is a size 12, which is somewhere between a current McCall’s 6 and 10. The vintage pattern’s bust is comparatively smaller than today with the same the waist and hip.
Pattern Tissue: the triangles for matching pieces together are numbered. Why don’t they do this anymore? I was surprised to find that the pattern tissue had French and Spanish wording as well as English.
Instruction Sheet: the pattern came with a single page of instructions, densely printed front and back. It seems like they did their best to utilize every bit of that space, making the text and illustrations tiny. But it’s all there: general sewing instructions, cutting layouts, and numbered step-by-step assembly instructions.
Some of the terminology has changed, but it’s easy enough to follow. Fabric is referred to as goods, waist refers to the top of the garment, slide fastener means zipper.
Common widths for “goods” were evidently different than they are today. Therefore, I had to figure out yardage estimates and layout on my own.
Because the pattern format has remained so similar over the years, anyone comfortable sewing from a “Big 4” pattern should not have any trouble.
Since the pattern is a single size, you may need to work a little harder to get it to match your measurements. You can’t just draw a line between a 12 waist and 14 hip. The instructions do explain how to make common changes, though.
You will want to think about modern techniques and tools that could help with construction such as fusible interfacing, overlocking, automatic buttonholes, fabric markers, and so on. Fabric options are also different today. Synthetics especially have come a long way since the 1940’s.
Read everything carefully and take notes. My pattern did not mention belt buckle and buttons on the pattern envelope’s materials list, but they are part of the written instructions. I don’t know if these kinds of omissions are common or not, but it never hurts to double check.
Sewing a dress using a vintage pattern was akin to making a cake using a vintage recipe. You might find yourself scratching your head as you go, but it’s a fun way to make a connection with the past. I’ll definitely consider vintage patterns again.
McCall’s pattern M6886 has a strong following. A recent search on patternreview.com found 203 reviews, with an average rating of 4.9/5 stars! It certainly warranted a closer look. It’s a pattern for a simple shaped knit dress with optional set-in sleeves, 2 length and 3 neckline options.
When my Mom recently came for a visit, we thought it would be a great choice for making her a fun new dress. I’ve never sewn garments for another person, so I was especially interested to see how well the fitting skills I developed for myself would translate.
The first part is always fun: a trip to the fabric store! We considered lots of options and finally landed on a vibrant textured nylon/lycra knit. It fit the bill as a medium weight moderate stretch knit. As a bonus, it is impossible to wrinkle, making it a great fabric for traveling. Because the print was so prominent, we chose the plainest neckline and the shorter knee-length.
Before cutting into the good fabric, I tissue-fit the pattern. I started with a pattern size based on Mom’s chest (not bust) measurement. This way, the neck and shoulders already fit the way they were supposed to. With a good fit above the bust, figuring out the rest was straightforward. With the tissue pinned to my model down the center line, I taped additional pattern paper around the sides to make the front and back meet. I could see right away that I would need to make darts to fit the bust. I folded the pattern paper to make the dart and taped that in place as well. I marked her actual bust apex, waist, and hip heights. With my model standing still and straight, I drew a line perpendicular to the floor from the underarm to the knee.
With the pattern unpinned, I set about creating new front and back pattern pieces. The perpendicular line became the new side seam. I added 5/8 inch seam allowance outside the seam line to make a new cutting line. I made the dart using a cut-and-slide technique, angling the dart to the actual bust point. I then checked to make sure the side seams matched by measuring inside the seam allowance on both sides. Whew! Finally time to cut into the fabric!
I basted the front and back pieces and checked the fit again. The fit was ok, but not great. The bust darts needed to be moved, but the back just looked loose and shapeless. We decided to add some shape with back darts. When I was happy with the new changes, I sewed them in place then transferred them to the pattern pieces.
By pure luck, I didn’t need to make any changes to the sleeves. The only departure from the pattern was to add 1 1/2 inches to the short sleeve length.
Once all of the fitting was done, sewing the dress was fairly simple. The only difficulty I had was figuring out how to mark the darts. I tried chalk, transfer paper and marking pens in various colors, but nothing showed up. I didn’t want to do tailor’s tacks mostly because I don’t like doing them, but also because they might create snags. So once again it was blue tape to the rescue!
I carefully positioned blue painter’s tape just outside the darts’ seam lines. I pinned the fabric as I would normally for darts. I then stitched the darts, keeping the needle just “kissing” the tape edge. Bonus: the tape stabilized the fabric while I sewed, so there was no risk of stretching the darts out of shape.
This project also marks the first time I have tried sewing with textured nylon thread. Instead of using all-purpose thread in my regular (not serger) machine, I used Maxi-Lock Stretch thread in the bobbin only. It really worked well. I thought the machine might have some difficultly with it, but I had no problems at all. The results were fantastic. All of the seams have nice stretchiness and recovery. I have no worries about any stitches breaking under a little pressure. I’m thinking about getting more in some neutral colors so I can use it in all of my knit sewing.
The edges are all finished with a truly invisible invisible hem (I hope I never have to pick it out!). The neckline is just a 1/4 inch narrow hem.
I managed to make this simple pattern much more complicated, but it fits Mom well (if I do say so myself!). Now I have a go-to pattern for her that can be used for dresses or even tee-shirts.
The last time I did some outlet shopping, I found some jeans that almost fit for $16 (yay, me!). The only problem was that they were over 4 inches too long. Fortunately, hemming pants is one of the easiest sewing projects there is. These were straight leg, making it even easier.
I followed my usual hemming process. Here’s a refresher:
Try on the jeans with shoes. Place a pin where you would like them to end.
Measure the distance from the bottom to the pin. Subtract your chosen hem allowance from this number.
Take out the pin. Measure up from the bottom the calculated number of inches and mark. Be careful to mark the same distance all the way around both legs.
Cut at the marked line.
Finish the raw edges with a 3 or 4 thread overlock stitch. (Any color will do – this stitching doesn’t show).
Turn the jeans inside out. Turn up the hems to your hem allowance and press. Turn right side out again.
Test your topstitching on the cut-off scraps. Topstitch the hem in place. Done!
To get the factory-made jeans look, the right topstitching is essential. When you think of jeans details, you think of heavy thread in shades of gold, white, and neutrals. I found that there are many options available. You can find thread made specifically for jeans, but any thread in the heavier weight ranges is worth considering. Think about whether you want soft or hard, matte or shiny, heavy or really heavy. Here are some to try:
You will need the right size needle for your thread. I used a size 14/90 universal needle for my TEX 60 weight thread. It worked well on the first try, so I didn’t try any other sizes. However, if I were to use a TEX 80 or 100 weight thread, I would go up to a 16/100. Schmetz, Klasse and Singer make a range of needles specifically for jeans which are supposed to be more durable when sewing through multiple layers. You can also get double needles. These are great if you want to be extra sure you stitch parallel lines and come with different spacing. I haven’t tried them yet, but if I get into sewing a lot of denim, I’m sure I will.
I never really thought about it before, but there isn’t any reason that the bobbin and the upper thread have to match. In fact, what seems to work best for jeans is a bobbin thread in a normal weight the same color as the denim.
Fortunately, my machine sews through thick fabrics and “bumps” without a hitch. I have found that with other machines a “hump jumper” can save a lot of frustration when going over seams. You can make your own with some folded tagboard or you can buy them ready-made. A walking foot can also help your machine cope with the thick layers.
Your machine shouldn’t need any tension or other fancy adjustments. You will just want to make sure it is sewing the longest possible straight stitch to start.
Once I had my machine set up, I lined up the bottom edge of the jeans with the edge of my presser foot. This worked well for stitching the first line. The second line was done in much the same way, just using the first line of stitching as my visual edge guide.
Now that I know how easy it is, I am going to topstitch all the time!
The Angelia Shorts pattern from Itch to Stitch Designs seemed to fit the bill. Itch to Stitch is another independent pattern company that sells downloadable PDF patterns. Itch to Stitch PDFs are available in “copy shop” versions, which is a big time saver. When you purchase the pattern, you get it in all of the available sizes. In this case, there are 12 sizes ranging from a waist measurement of 23 7/8 to 39 inches. You can choose to turn the cutting lines for each size on or off, which really helps when you have so many sizes on one sheet.
The basic shorts are slightly below waist with loose fitting legs, a waistband and front zipper fly. There are length variations starting at a 4 inch inseam and all kinds of options for pockets, belt loops, and so on.
I made a quick muslin to test just the main front and back pieces for fit. I did not worry about the closure – I just pinned the center shut. I found that I needed to taper the sides a little and widen the darts. I transferred the changes to my front and back pattern pieces, then adjusted the waistband piece to compensate for the darts. Now I was ready to test the whole pattern.
Back – Before
Back – After
Side – Before
Front – After
I made my wearable muslin out of quilting cotton (Orient by Nel Whatmore). Yes, it’s a little busy, but I have to be me! I have to say that I was impressed by the instructions provided by Itch to Stitch. They don’t assume any garment sewing experience, so there are detailed steps for things like making pattern alterations and shortening a zipper. I followed the instructions closely, since I had never made a zipper fly closure before. It worked! I was not confused by any of the potentially confusing steps and I’m really pleased with how the closure turned out. Here’s a slideshow of the closure construction:
I’m really glad I made a test version, because I could see right away that I needed to make more changes. The main issue is that the crotch sits too low. I pinned out a slightly shorter crotch length and transferred the change to my pattern pieces. I feel like I am now ready to go with any of the pattern options.
Stay tuned for a “bells and whistles” version. In the meantime, happy sewing!
I had a lot of fun last week putting together some cute lightweight tee shirts. Vogue V8792 has been on my to-sew list for a while. I initially chose it because I liked the interesting way the stripes were positioned on the top in the cover photo. Did I mention I love stripes? But when I started looking at the details, I was really intrigued by the short sleeve views (A, B, C). The long and the short sleeve shirts are completely different, not just the same shirt with options. The long sleeve versions are fitted and have set-in sleeves. The short sleeve ones are loose fitting and made from only 3 pieces: front, back and neckband. The front and back are cut on the bias and attach together like a puzzle. That sounded like a lot more fun!
My first version used a lightweight gray rib knit with a subtle heathered stripe. I thought the stripe would create an interesting effect where the two bias pieces met. It went together quickly on the serger – cutting it out took about the same amount of time as sewing. I was surprised that I didn’t see the effect I was expecting though. It turns out that I somehow ignored the layout directions and cut the front and back pieces on grain instead of on bias. Oops. The shirt is still nice, still wearable, but a little disappointing.
Since it was so easy to make, I thought I would give it another try and see if I would like it better if I followed the instructions! I made two more, both using a mix of different colors.
The second tee used up a pretty mottled green remnant that was about 1/4 yard long and full width. I paired it with a sheer cream color knit that was a little too transparent to use on the front. I made the neckband a little wider than the pattern called for, but otherwise this one followed the pattern instructions. The difference is subtle when there is no obvious stripe, but I think the shirt may drape a little better than the gray one.
The third tee gave me an opportunity to try a color combination I love: sky blue and white. There isn’t a lot to add about this one, but isn’t it cute?
The design is printed on a very stretchy cotton/lycra jersey. You could easily use this stable fabric for leggings or activewear. So I took a cue from the athleisure trend and settled on a casual, pull-on circle skirt.
Circle skirts don’t really need a pattern, but they do require a little thought and planning. I used Mood Fabrics’ circle skirt calculator to get a general idea of what I could make with my 2-yard cut. You can see what the possibilities are for 3 skirt lengths and 3 types of skirt: half, 3/4, and full circle skirts. If you want to maximize the length, you would choose a full circle. If you don’t like the fullness of a full circle, you can make a 1/2 or 3/4 circle, but you will sacrifice some length. I compromised and chose a happy medium 3/4 circle.
The large rose and peony (?) blooms run vertically down the fabric selvedge. I wanted to make sure I placed them on the skirt to maximum advantage. Luckily, I found an image of the exact design on google. The image even worked out to the same ratio as a 2 yard cut. I saved the image, then marked it up with several possible cutting layouts. To make it even easier to visualize, I used some scissors and tape and made little scale models of my favorites. It really helped and only took a few minutes.
Construction was super simple. I only had to serge together one vertical seam and a waistband. The waistband is simply a rectangle from the same fabric made into a tube, folded once and serged to the skirt opening.
The only construction detail on a circle skirt like this that requires any technique is the hem. Hemming a curved edge usually requires extra steps to manage the difference in circumference between the bottom edge and the seam line. I have to admit that I didn’t want to bother with all that. I also thought the stretchy material, which does not fray could look nice with just a rolled hem. As a bonus, it would maximize the amount of the floral design that shows.
Having made that decision, I set about marking a level line around the skirt’s bottom edge. To do the marking myself, I rigged a hemming assistant with my duct-tape model, a tripod, and a command-adhesive cord bundler attached to the ceiling. I was delighted with how well it worked. Once I got it set up, it was pretty stable. It was also a much more comfortable working position. I made sure the model’s posture was correct, then pinned the skirt level around the waist. I took a carpenter’s tape measure (my yardstick was too short), measured and marked the skirt an equal distance up from the floor. I’ll definitely be using this trick again!
I know that when I try on fuller ready to wear skirts, they typically hang lower in the front than the back. I was still surprised that I ended up trimming off 4 inches to make the front match the back. No wonder!
Place a pin at the same distance from the floor all the way around.
Mark the new cut line on the reverse using pins as a guide
The last step was to stitch the rolled edge. Of course, I did a few test runs with scraps. Somewhere along the line, I thought instead of hiding the edge, I would highlight it. So the final version features a narrow line of hot pink stitching. It’s subtle, but I think it enhances the design.
Assembling the waistband
Close up of rolled edge
I can see this skirt as something easy to pull on after a workout. But I can just as easily see it dressed up. A very comfortable, easy to make project, but special too.
As a nod to Saturday’s 144th running of the Kentucky Derby, I’m calling this one the Run for the Roses skirt.
Independent pattern company Love Notions sells a blouse with a loose, peasant style bodice entitled Rhapsody. I love wearing this kind of top in warmer weather and have been looking for a good pattern. What made Rhapsody stand out from the others was their 8 different sleeve options: sleeveless, cap, short, 3/4 with cuff, 3/4 with flare, trumpet, flutter, and bishop. Whew!
Love Notions sells multi-size downloadable PDF patterns. You can print them at home and tape together your printouts, or you can do what I do and send it off to be printed onto large single sheets. (Right now, the best deal seems to be pdfplotting.com). I was delighted by the thorough instructions Love Notions provides as part of the download. In addition to the usual stuff, they include color photos of tricky steps and links to instructional videos.
Rhapsody is designed to be made with lightweight wovens. All of the versions have narrow bias bound necklines, so you also either need purchased or handmade bias tape.
Since the Marfy short sleeve top didn’t use up all of the pretty cotton lawn fabric, I thought there might be enough to make a Rhapsody. I laid my scraps and pattern pieces on the cutting table to see if I could make it work. I almost had enough to make the sleeveless version, but nothing was wide enough for the single piece back. I changed things around a little so the back was made from two pieces instead and just barely made it all fit.
I did not have enough scrap left to make narrow bias binding, so I found some plain white pre-made in my stash. I think it’s a good idea to keep a few sizes of basic colors on hand just in case. I’ll stock up on black, white, navy and red (those are my basics anyway) whenever I see a bargain.
Before I put it all together, I thought about how I could embellish it to stand apart from my other top. I played around with all of my scrap trimmings to see what looked good. The curved bottom edge didn’t look right with any trim, but the front came alive with a faux placket. I just sewed two lengths of cotton lace an equal distance from the center front before doing anything else.
Remember those pockets I couldn’t find a use for? I think they look like they are made to go on the Rhapsody.
Again going through my stash, I found a couple of buttons that looked good on the pocket fronts. Initially, I was going to put a row down the placket, but with the ties (or bow) at the neck, it was just one thing too many.
Assembly included many different techniques. There are french seams, tucks, gathering, narrow hems and bias trimmed neck opening. Even if you have no experience, the instructions should get you through it. Applying binding to a V-neck is a tricky proposition, but I was able to do it perfectly the first time by following their tutorial.
I think it turned out great, albeit a little tight across the back. I scooped out the armholes by about 1/4 inch, which helped. Next time I will try a wider yoke, or possibly go up an entire size. There will definitely be a next time for this one. I really want to try out some of the different sleeves.